Gyptech Gypsum Plaster and Jointing Compound

Gyptech Gypsum Plaster

Gyptech Jointing Compound

Gyptech Gypsum Plaster

Range of Gypsum Plaster Products

Universal Plaster
Stuco Plaster
Veneer Plaster


Universal Plaster is a premixed single application plaster made from calcium sulphate hemihydrate to which additives have been added to improve performance and work ability.

Technical Specifications

Color of finished surface : White
Bulk Density kg/m3 : 1120
Setting Time/minutes : 25-30
Coverage of 25 Kg Bag at 13mm (thickness) : 18-19 sq. ft.
Compressive Strength Kg/Cm2 : 70-80

Salient Features

Premixed light weight plaster
Easy workability : Easy to mix - Easy to apply
Free from inherent shrinkage cracks
Classified as non-combustible (BS:476 part 4:1970)
Low Thermal Conductivity (Thermal Resistance R=0.07m2 k/w, 13mm thickness)
Light Weight - Better strenght to weight ratio as compared to density
Achieves total strength with 48 hours on complete drying (Quick drying)
Low density, Better sound absorption, Better paint coverage
Less water consumption - 15 liter water required for 25kg plaster. Water curing is not required


GYPTECH – Universal Plaster


Sand & Cement Plaster

Low Density | High Density
Low Thermal Conductivity and hence obstructs flow of heat. | Thermal Conductivity High compared to Vermiculite
Because of uniform porosity humidity is under control | Control of humidity is negligible
No cracks because of its resilient nature | Cracks may appear with appreciable changes in temperature
Excellent smoothness and whiteness improves the aesthetic appeal of the surface after painting | Additional costly treatments are required to get good smooth finish
No curing required. Painting can be taken up after 48 hours of complete drying. Time saving. | Requires two weeks of curing and surfacing. Time consuming.
Good sound absorption | Reflects sound

Guidelines for Application

Fitting & plugging should be done before plastering. Openings, chasing etc. (for fittings or conduits) should be filled firmly before starting plastering.
Entire background (to be plastered) should be thoroughly brushed & cleaned to remove dust, loose mortar & oil/grease.
The surface should be reasonably dry & protected from weather conditions. The high suction background should be adjusted by sprinkling water.
Always mix powder to water, not water to powder. Material should be thoroughly mixed & stirred as to ensure it is free from lumps and impurities before use.
Once plaster wet mix is made & has started to do set, it should not be tempered with fresh mix or powder, as it will affect the properties.
Due care should be taken to ensure that rapid loss of water is avoided, in hot & dry condition.
Tools & water used should be cleaned & free from impurities.
To ensure that hands are dry before putting them in the bag. After taking out plaster, always fold open end of bag to protect plaster from moisture.
Bags should be handled carefully to avoid tearing. Hooks are not recommended.

Basic Important Facts

The consumption of Gyptech Gypsum Plaster is directly related to the line & level of walls in the building, which is a variable factor. It also depends upon the basic wall base material i.e. Bricks or Blocks.
Based on field trials & experience, the consumption pattern of Gypsum plaster varies between 1.5 kg to 2 kg per square feet for 13mm thickness of plaster in right angle finish on the walls.
It is advisable to do a mock-up of an entire flat in your building to ascertain the actual consumption pattern of Gypsum Plaster.

Gyptech Gypsum Jointing Compound

Gyptech Gypsum Jointing Compound is used for finishing Gypsum Board Joints

Consistent setting time
Low shrinking
Excellent tape bonding strength
Easy to apply
Easy mixing

© 2018 Gyptech Systems Pvt. Ltd. | All rights reserved | Design by W3layouts